![]() ![]() The computer cannot be running Windows 95, Windows 98, or Windows Millennium Edition. You can start Winnt32.exe with the /syspart option on an x86-based computer running Windows NT 4.0, Windows 2000, or Windows XP Professional. You must always use the /tempdrive parameter with the /syspart parameter. When you start the computer onto which you have installed the disk, it automatically starts with the next phase of Setup. syspart - On an x86-based computer, this parameter specifies that you can copy Setup startup files to a hard disk, mark the disk as active, and then install the disk onto another computer. noreboot - Instructs Setup not to restart the computer after the file-copy stage of Setup finishes, so that you can execute another command. The i386 files will be taken from the same folder that winnt32.exe is located when it is run. Use /makelocalsource when installing from a CD to provide installation files when the CD is not available later in the installation. makelocalsource - Instructs Setup to copy all installation source files to your local hard disk. D:\XPHOME\i386 or D:\XPPRO\i386 just change the winnt32.exe path accordingly. (thanks to João Santos for the tip of adding /makelocalsource!). if D: is the USB drive) to start the copy of the XP install files to the hard disk as follows:ĭ:\i386\winnt32.exe /unattend10:J:\i386\unattend.txt /syspart:J: /tempdrive:J: /makelocalsource Now you need to run winnt32.exe from the drive containing the source i386 folder (e.g. You now should have a formatted hard disk ready to receive files.ĥ. SEL DIS 0 select disk zero (usually the first hard disk)ĬRE PAR PRI SIZE=30000 ALIGN=16065 create a 30GB primary partition for XP (change as required) - if this gives an error use 64260 instead of 16065.įOR QUICK LABEL=SYSTEM format it as NTFS (add FS=FAT32 if you don't want an NTFS partition)ĪSSIGN LETTER=J assign it the drive letter J:ĬRE PAR PRI create another NTFS partition of remaining size (optional)ĪSSIGN assign it a drive letter (optional) Now run DISKPART and type the following commands (assuming you want a two partitions on the hard disk) - only type the commands (shown in capital letters): Boot from the WinPE USB drive using the target system that you wish to install Windows XP onto. The USB drive should now contain an \XPPRO folder as well as the winpe folders: \sources, \boot, etc.ģ. Note: NTFS formatting is recommended for speed. Now prepare a WinPE v3 (bootmgr) bootable USB drive using RMPrepUSB and copy over the C:\MYXP folder to the USB drive - please refer to the part 2 of my tutorial here. Note: XP does not contain AHCI or some SCSI/SATA drivers - either you must set your BIOS menu for Hard Disk mode to 'compatible/legacy' hard disk mode or you must use a specially modified version of XP (e.g. Obtain a Microsoft Windows XP installation CD or ISO or set of NLited files that you wish to installĬreate a new folder on your Windows (office computer) hard disk called C:\MYXP\XPPRO\i386 (assuming you have XP Professional)Ĭopy all the files in the CD's i386 folder to C:\MYXP\XPPRO\i386 folderĮnsure that the file C:\MYXP\XPPRO\i386\unattend.txt is present and has been correctly modified by you (see end of this page for an example) You can create either an x86 version (recommended) or an amd64 (64-bit) version.Ĭreate a new folder C:\MYXP on your office computer.Ĭopy the c:\pe86\ISO folder contents to C:\MYXP (C:\MYXP should now contain bootmgr, folders \boot, \sources, \efi, etc.)Ģ. Download and install the Windows 7 WAIK to obtain the ImageX utility and WinPE filesįor instructions on how to do this, please refer to the first part of my tutorial here or follow the Make_PE3 tutorial.įollow the instruction up to the point where a WinPE folder has been created (Step 1) Run winnt32.exe (the file will be on the hard disk after copying from the USB drive)ġ. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |